Installation of Twonky Server 7 on NAS-devices

After a few requests i’ve now tried to install Twonky Server 7 on the NAS_Devices and i can tell you that it works. The following article describes the installation. Before you proceed please check here if Version 7.11-Special is still the current version. If not, please add a comment below.

This tutorial requires an installed fun_plug!

Continue reading Installation of Twonky Server 7 on NAS-devices

Installation of Optware on the D-Link DNS-323 and Conceptronic CH3SNAS

Many people asked me to compile various packages over the last few years. Sometimes i was able to help and sometimes (in rare occasions) i had to reject a request when it was impossible to fulfill it. Then i often told the requestor to install optware which originated from the NSLU2-Project and provides many addition packages. I didn’t have experienc on this, so i had to leave them in the dark. Until recently. Continue reading Installation of Optware on the D-Link DNS-323 and Conceptronic CH3SNAS

Installation of the Conceptronic fun_plug on the Conceptronic CH3HNAS

Since a while the Conceptronic CH3HNAS has been around which – unfortunately – is not compatible with the Fonz’ fun_plug due to a different CPU. Conceptronic themselves provides a fun_plug package which solves that issue. If you don’t know what the fun_plug is, then read the introduction of this article until including “Technical synopsis” for further explanation. Here is how the Conceptronic fun_plug is installed on the CH3HNAS:

  • Download the package from Conceptronic: Download (Mirror by Uli)
  • Extract the package on your local harddrive
  • Navigate to folder “Funplug” and copy the files “fun_plug” and “fun_plug.tgz
  • Navigate to the “Public”-Folder on your CH3HNAS and paste these two files there
  • Then login to the Webpanel of your NAS and go to “Tools” -> “System” -> “Restart” to reboot your device
  • After the reboot, the CH3HNAS will discover the fun_plug and install it on the harddrive. Be patient as it takes a while to install the fun_plug
  • After a while the fun_plug.tgz will disappear and a folder called “funplug” will appear instead.
  • A Telnet-Server is now available on Port 23 on your CH3HNAS

That’s it!

Update of Twonkymedia Server 6 on the Conceptronic CH3MNAS, D-Link DNS-320,DNS-321,DNS-325 and DNS-343

This tutorial is deprecated, please use the tutorial for the current version.

Since a while there is a new version of the Twonkymedia Server 6 available. Many readers asked me how to update to this version without loosing the configuration of the already installed version. This article describes the update for the following devices:

  • Conceptronic CH3MNAS
  • D-Link DNS-320
  • D-Link DNS-321
  • D-Link DNS-325
  • D-Link DNS-343

For other devices, please follow this article. If you are searching for the article regarding the initial installation (not the update), please look here for this.
Continue reading Update of Twonkymedia Server 6 on the Conceptronic CH3MNAS, D-Link DNS-320,DNS-321,DNS-325 and DNS-343

Update of Twonkymedia Server 6 on the Conceptronic CH3SNAS and the D-Link DNS-323

This tutorial is deprecated, please use the tutorial for the current version.

Since a while there is a new version of the Twonkymedia Server 6 available. Many readers asked me how to update to this version without loosing the configuration of the already installed version. This article describes the update for the following devices:

  • Conceptronic CH3SNAS
  • D-Link DNS-323

For other devices, please follow this article. If you are searching for the article regarding the initial installation (not the update), please look here for this.
Continue reading Update of Twonkymedia Server 6 on the Conceptronic CH3SNAS and the D-Link DNS-323

Output of dmesg on the Conceptronic CH3WNAS

Here the output of dmesg on the Conceptronic CH3WNAS:

Total memory 33554432 MB.
Memory BAT mapping: BAT2=32Mb, BAT3=0Mb, residual: 0Mb
Total memory is 33554432.
CPU = 82xx
Linux version 2.4.21-pre4 (ffna@swtest2) (gcc version 2.95.4 20010319 (prerelease)) #480 �� 4�� 28 11:21:43 CST 2006
OpenPIC_Addr in mpc10x_bridge_init function is fc040000
Motorola SPS Sandpoint Test Platform
Port by MontaVista Software, Inc. (source@mvista.com)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=ttyS0,9600
OpenPIC Version 1.2 (1 CPUs and 123 IRQ sources) at fc040000
Calibrating delay loop... 133.12 BogoMIPS
Memory: 27368k available (1560k kernel code, 512k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI fixup irq: (PCI device 1814:0201) got 0
PCI fixup irq: (PCI device 1033:0035) got 1
PCI fixup irq: (PCI device 1033:0035) got -1
PCI fixup irq: (PCI device 1033:00e0) got 2
PCI fixup irq: (PCI device 13f0:1023) got 3
PCI fixup irq: (PCI device 1191:0008) got 4
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
NTFS driver v1.1.22 [Flags: R/W]
udf: registering filesystem
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SERIAL_PCI enabled
ttyS00 at 0xfc004500 (IOMEM)(irq = 121) is a ST16650
ttyS01 at 0xfc004600 (IOMEM)(irq = 122) is a ST16650
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
loop: loaded (max 8 devices)
ipg : v0.36 10/31/01 Written by Craig Rich, www.sundanceti.com
IC PLUS IP1000 1000/100/10 based NIC found.
Ethernet device registered as: eth0
IPG module loaded.
SCSI subsystem driver Revision: 1.00
atp86x_detect:
ACARD ATP-865 PCI ATA133 2-Channels Host Adapter: 0 IO:FEBFFEF8, IRQ:4.
ID: 0 ST3200822A UDMA5 (100)
scsi0 : ACARD ATP86X PCI ATA133 Adapter Driver Ver: 0.78 Date: 2004/01/15
 
Vendor: ST320082 Model: 2A Rev:
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 390721967 512-byte hdwr sectors (100025 MB)
Partition check:
sda1 sda2
USI AMD/FUJITSU flash: probing 8-bit flash bus
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 5 MTD partitions on "USI Intel flash":
0x00000000-0x00010000 : "Linux mtd1"
0x00010000-0x00020000 : "Linux mtd2"
0x00020000-0x00300000 : "Linux Ramdisk"
0x00300000-0x00310000 : "U-BOOT BOOT LOADER"
0x00310000-0x00400000 : "Linux Kernel"
usb.c: registered new driver hub
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2879k freed
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 60k init
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
bonding.c:v2.4.20-20021210 (December 10, 2002)
br0 registered with MII link monitoring set to 100 ms, in fault-tolerance (active-backup) mode.
br0 registered without ARP monitoring
br0: released all slaves
Link speed = undefined!
Link speed = undefined!
br0: enslaving eth0 as a backup interface with a down link.
Link speed = 100Mbps.
setting full duplex, TX flow control, RX flow control.
br0: link status definitely up for interface eth0.
and making interface eth0 the active one.
br0: releasing active interface eth0 but could not find any backup interface.
br0: now running without any active interface !
Link speed = undefined!
Link speed = undefined!
br0: enslaving eth0 as a backup interface with a down link.
br0: releasing backup interface eth0.
br0: now running without any active interface !
Link speed = undefined!
br0: enslaving eth0 as a backup interface with a down link.
Adding Swap: 530104k swap-space (priority -1)
ext3: No journal on filesystem on sd(8,2)
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
ehci_hcd 00:0e.2: PCI device 1033:00e0
ehci_hcd 00:0e.2: irq 2, pci mem c306af00
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 5 ports detected
usb-ohci.c: USB OHCI at membase 0xc3073000, IRQ 1
usb-ohci.c: usb-00:0e.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xc3075000, IRQ -1
usb-ohci.c: usb-00:0e.1, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 3
request_irq irq >= NR_IRQS fail
usb-ohci.c: request interrupt -1 failed
usb.c: USB bus 3 deregistered
Trying to vfree() nonexistent vm area (c3075000)
ra0: at 0xbfffe000, VA 0xc30a3000, IRQ 0.
ra0: RT2500_open() irq 0. MAC = 00:80:5a:5c:63:20
Link speed = 100Mbps.
setting full duplex, TX flow control, RX flow control.
br0: link status definitely up for interface eth0.
and making interface eth0 the active one.
pAdapter->PortCfg.StaWithEtherBridge.Enable = FALSE
bond_enslave(): MII and ETHTOOL support not available for interface ra0, and arp_interval/arp_ip_target module parameters not specified, thus bonding will not detect link failures! see bonding.txt for details.
br0: enslaving ra0 as a backup interface with an up link.
br0: releasing backup interface ra0.
br0: releasing active interface eth0 but could not find any backup interface.
br0: now running without any active interface !
br0: released all slaves
NET4: Ethernet Bridge 008 for NET4.0
device eth0 entered promiscuous mode
Link speed = undefined!
Link speed = undefined!
br0: port 1(eth0) entering listening state
device ra0 entered promiscuous mode
br0: port 2(ra0) entering listening state
Link speed = 100Mbps.
setting full duplex, TX flow control, RX flow control.
br0: port 1(eth0) entering learning state
br0: port 2(ra0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
Initializing USB Mass Storage driver...
my_host_number = 1
usb.c: registered new driver usb-storage
USB Mass Storage support registered.

Output of /proc/meminfo on the Conceptronic CH3WNAS

Here the output of cat /proc/meminfo on the Conceptronic CH3WNAS:

      total:    used:    free:     shared:  buffers:  cached:
Mem:  31035392  30347264 688128    0        1609728   22712320
Swap: 542826496 5353472  537473024
MemTotal:    30308 kB
MemFree:       672 kB
MemShared:       0 kB
Buffers:      1572 kB
Cached:      18508 kB
SwapCached:   3672 kB
Active:      16416 kB
Inactive:     7728 kB
HighTotal:       0 kB
HighFree:        0 kB
LowTotal:    30308 kB
LowFree:       672 kB
SwapTotal:  530104 kB
SwapFree:   524876 kB

Output of /proc/meminfo on the Conceptronic CH3HNAS

Here the output of cat /proc/meminfo on the Conceptronic CH3HNAS:

MemTotal:        60980 kB
MemFree:          2336 kB
Buffers:          8128 kB
Cached:          33552 kB
SwapCached:          0 kB
Active:          11780 kB
Inactive:        33072 kB
SwapTotal:           0 kB
SwapFree:            0 kB
Dirty:               8 kB
Writeback:           0 kB
AnonPages:        3192 kB
Mapped:           3304 kB
Slab:             7136 kB
SReclaimable:     3936 kB
SUnreclaim:       3200 kB
PageTables:        256 kB
NFS_Unstable:        0 kB
Bounce:              0 kB
CommitLimit:     30488 kB
Committed_AS:     8504 kB
VmallocTotal:   253952 kB
VmallocUsed:     13700 kB
VmallocChunk:   237564 kB

Output of /proc/cpuinfo on the Conceptronic CH3HNAS

Here the output of cat /proc/cpuinfo on the Conceptronic CH3HNAS:

Processor       : ARM926EJ-S rev 5 (v5l)
BogoMIPS        : 183.09
Features        : swp half thumb fastmult edsp java
CPU implementer : 0x41
CPU architecture: 5TEJ
CPU variant     : 0x0
CPU part        : 0x926
CPU revision    : 5
Cache type      : write-back
Cache clean     : cp15 c7 ops
Cache lockdown  : format C
Cache format    : Harvard
I size          : 32768
I assoc         : 4
I line length   : 32
I sets          : 256
D size          : 32768
D assoc         : 4
D line length   : 32
D sets          : 256
 
Hardware        : Oxsemi NAS
Revision        : 0000
Serial          : 00000acbcbed6e00
Exit mobile version