Here the output of dmesg on the Conceptronic CH3WNAS:
Total memory 33554432 MB. Memory BAT mapping: BAT2=32Mb, BAT3=0Mb, residual: 0Mb Total memory is 33554432. CPU = 82xx Linux version 2.4.21-pre4 (ffna@swtest2) (gcc version 2.95.4 20010319 (prerelease)) #480 �� 4�� 28 11:21:43 CST 2006 OpenPIC_Addr in mpc10x_bridge_init function is fc040000 Motorola SPS Sandpoint Test Platform Port by MontaVista Software, Inc. (source@mvista.com) On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/ram console=ttyS0,9600 OpenPIC Version 1.2 (1 CPUs and 123 IRQ sources) at fc040000 Calibrating delay loop... 133.12 BogoMIPS Memory: 27368k available (1560k kernel code, 512k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware PCI fixup irq: (PCI device 1814:0201) got 0 PCI fixup irq: (PCI device 1033:0035) got 1 PCI fixup irq: (PCI device 1033:0035) got -1 PCI fixup irq: (PCI device 1033:00e0) got 2 PCI fixup irq: (PCI device 13f0:1023) got 3 PCI fixup irq: (PCI device 1191:0008) got 4 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded NTFS driver v1.1.22 [Flags: R/W] udf: registering filesystem Serial driver version 5.05c (2001-07-08) with MANY_PORTS SERIAL_PCI enabled ttyS00 at 0xfc004500 (IOMEM)(irq = 121) is a ST16650 ttyS01 at 0xfc004600 (IOMEM)(irq = 122) is a ST16650 RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize loop: loaded (max 8 devices) ipg : v0.36 10/31/01 Written by Craig Rich, www.sundanceti.com IC PLUS IP1000 1000/100/10 based NIC found. Ethernet device registered as: eth0 IPG module loaded. SCSI subsystem driver Revision: 1.00 atp86x_detect: ACARD ATP-865 PCI ATA133 2-Channels Host Adapter: 0 IO:FEBFFEF8, IRQ:4. ID: 0 ST3200822A UDMA5 (100) scsi0 : ACARD ATP86X PCI ATA133 Adapter Driver Ver: 0.78 Date: 2004/01/15 Vendor: ST320082 Model: 2A Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sda: 390721967 512-byte hdwr sectors (100025 MB) Partition check: sda1 sda2 USI AMD/FUJITSU flash: probing 8-bit flash bus Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. Creating 5 MTD partitions on "USI Intel flash": 0x00000000-0x00010000 : "Linux mtd1" 0x00010000-0x00020000 : "Linux mtd2" 0x00020000-0x00300000 : "Linux Ramdisk" 0x00300000-0x00310000 : "U-BOOT BOOT LOADER" 0x00310000-0x00400000 : "Linux Kernel" usb.c: registered new driver hub NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 2048) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 2879k freed VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 60k init EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended bonding.c:v2.4.20-20021210 (December 10, 2002) br0 registered with MII link monitoring set to 100 ms, in fault-tolerance (active-backup) mode. br0 registered without ARP monitoring br0: released all slaves Link speed = undefined! Link speed = undefined! br0: enslaving eth0 as a backup interface with a down link. Link speed = 100Mbps. setting full duplex, TX flow control, RX flow control. br0: link status definitely up for interface eth0. and making interface eth0 the active one. br0: releasing active interface eth0 but could not find any backup interface. br0: now running without any active interface ! Link speed = undefined! Link speed = undefined! br0: enslaving eth0 as a backup interface with a down link. br0: releasing backup interface eth0. br0: now running without any active interface ! Link speed = undefined! br0: enslaving eth0 as a backup interface with a down link. Adding Swap: 530104k swap-space (priority -1) ext3: No journal on filesystem on sd(8,2) EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended ehci_hcd 00:0e.2: PCI device 1033:00e0 ehci_hcd 00:0e.2: irq 2, pci mem c306af00 usb.c: new USB bus registered, assigned bus number 1 ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 hub.c: USB hub found hub.c: 5 ports detected usb-ohci.c: USB OHCI at membase 0xc3073000, IRQ 1 usb-ohci.c: usb-00:0e.0, PCI device 1033:0035 usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected usb-ohci.c: USB OHCI at membase 0xc3075000, IRQ -1 usb-ohci.c: usb-00:0e.1, PCI device 1033:0035 usb.c: new USB bus registered, assigned bus number 3 request_irq irq >= NR_IRQS fail usb-ohci.c: request interrupt -1 failed usb.c: USB bus 3 deregistered Trying to vfree() nonexistent vm area (c3075000) ra0: at 0xbfffe000, VA 0xc30a3000, IRQ 0. ra0: RT2500_open() irq 0. MAC = 00:80:5a:5c:63:20 Link speed = 100Mbps. setting full duplex, TX flow control, RX flow control. br0: link status definitely up for interface eth0. and making interface eth0 the active one. pAdapter->PortCfg.StaWithEtherBridge.Enable = FALSE bond_enslave(): MII and ETHTOOL support not available for interface ra0, and arp_interval/arp_ip_target module parameters not specified, thus bonding will not detect link failures! see bonding.txt for details. br0: enslaving ra0 as a backup interface with an up link. br0: releasing backup interface ra0. br0: releasing active interface eth0 but could not find any backup interface. br0: now running without any active interface ! br0: released all slaves NET4: Ethernet Bridge 008 for NET4.0 device eth0 entered promiscuous mode Link speed = undefined! Link speed = undefined! br0: port 1(eth0) entering listening state device ra0 entered promiscuous mode br0: port 2(ra0) entering listening state Link speed = 100Mbps. setting full duplex, TX flow control, RX flow control. br0: port 1(eth0) entering learning state br0: port 2(ra0) entering learning state br0: port 1(eth0) entering forwarding state br0: topology change detected, propagating br0: port 2(ra0) entering forwarding state br0: topology change detected, propagating Initializing USB Mass Storage driver... my_host_number = 1 usb.c: registered new driver usb-storage USB Mass Storage support registered.