This procedure allows you to upgrade (or downgrade) the version of the firmware running on the NAS. Although backups are always nice (if you have that option), the data stored on the NAS is not affected. Similarly, any servers (daemons) running under fun_plug are also unaffected (although they are temporarily turned off and later turned on again).
Note that this somewhat elaborate procedure is needed if you are running fun_plug. If you do not have fun_plug installed, or it is no running, you can should use the simpler instructions provided by Conceptronic with the firmware file.
Checking the firmware version
You can tell which firmware version you are running by using a web browser:
- browse to the CH3SNAS using an IP address (default is http://192.168.0.20) or a network name (maybe http://CH3SNAS)
- If this brings you to a web page you created yourself, you are likely running fun_plug and have the lighttpd HTTP server running on port 80 and need to use port 81 to reach the configuration screen (e.g. using http://192.168.0.20:81). If you don’t know what funplug is, you are not using it and you can ignore this comment.
- login as admin
- Then go to: ”Configuration” >> ”Tools” >> ”Firmware”
Downloading firmware versions
An overview of the current stable version, any more recent beta (or “Release Candidate”) versions, or older versions can be found here.
The page contains links to sites where the firmware can be downloaded. After downloading the required version you will need to unzip or unrar it.
Installation if you don’t use
If you are not running fun_plug, you can simplify things by following the instructions in the PDF readme file supplied with the downloaded firmware rather than following the fancier instructions below which assume you may be running various special servers and running with special settings.
So, in the following, we assume that you are running fun_plug.
Temporarily reactivate Telnet
If you are running funplug, it is likely that you enabled
ssh (Secure Shell) and disabled
telnet for security reasons. After the reboot, all modifications to
/etc/group are gone, which is why we need to temporarily reactivate
telnet to ensure that we can login after the upgrade:
ssh(e.g. using PuTTY)
- activate the
telnetdaemon so you can easily login later:
cd /ffp/start ls -al telnetd.sh chmod a+x telnetd.sh ls -al telnetd.sh
This means that on the next reboot telnet should be enabled.
Notes on CH3SNAS Firmware 1.05 regarding the fan
If you are upgrading from a pre-1.0.5 firmware version to version 1.0.5 or later, you may decide to replace the special fan control script “
fanctl” from Fonz (see the fan control tutorial) with the standard fan control feature built into the Conceptronic firmware.
Which option is better? The firmware version 1.0.5 has a very simple fan control algorithm. The fan only runs when the internal temperature is 43°C or higher. This is a bit high. Furthermore, the fan speed does not depend on the temperature: the fan is either on or off. Fonz’ solution instead increases the fan speed as the temperature rises. This avoids the fan repeatedly turning on and off when the fan needs to spin, but doesn’t need to run at full speed.
If you decide to try the firmware’s solution, you can deactivate Fonz’ control program using:
cd /ffp/start sh fanctl.sh status ls -al fanctl.sh chmod a-x fanctl.sh ls -al fanctl.sh
Temporarily disable funplug
Rename the file
fun_plug.bak to deactivate ffp on the next boot. You can easily do this using e.g. Windows Explorer or using the command shell:
cd /mnt/HD_a2 ls fun_plug* mv fun_plug fun_plug.bak ls fun_plug*
Write down any special configurations you have set up in the system.
The main place to look is in the ”Advanced” tab of the Configuration web page. Write down a reminder to set any particular settings such as ”’users”’ who have access, ”’groups”’ you may have created, ”’ftp access”’ you may have given to groups, etc. If you forget to reconfigure these, you will find out later when e.g. an ftp account doesn’t work. Unfortunately there is no simple way to save these settings and later reload them: you will, for example, have to reenter or define new passwords.
Installing new firmware
Update the firmware via the web interface (see picture above). During the update, you will get a progress bar. Then, after confirmation, the CH3SNAS will reboot.
Next reset the CH3SNAS firmware settings to the factory defaults (the new firmware may interpret settings stored in Flash memory differently that the previous version). This step is mandatory to ensure correct operation!
- Open the configuration page
Restore To Factory Default Settings
This will cause another reboot during which the IP address, group/user information, user privileges will be lost. Your browser may not find the device again if you use a non-default name. Try the default “http://CH3SNAS/” or using Conceptronic’s “Easy Search Utility” to find your NAS in the network.
At this point, the administrator password is empty, so you can log onto the Config web page as
admin with an empty password. Then you need to run
Run Wizard to get the basic settings correct again. These include
- the admin password
- timezone and daylight savings time setting
- IP address (if set to static)
- the network workgroup
- the network name of the CH3SNAS
At this point you cannot access the CH3SNAS via either
ssh because an out-of-the-box CH3SNAS does not enable either daemon:
fun_plugusing SAMBA (e.g. using Windows Exporer)
- reboot the CH3SNAS (e.g. using the Configuration page:
Note that before the reboot, your Config page is on port 80. It may be on port 81 after the reboot. From this point on
telnetshould work again.
- Login with
telnetand set the root password again using this procedure. This ends with running
store-passwd.shto save the password information.
telnetagain (first be sure
sshis running!) using an ssh session on PuTTY:
cd /ffp/start ls -al telnetd.sh chmod a-x telnetd.sh ls -al telnetd.sh sh telnetd.sh stop
The final line stops the telnet daemon, so from this point on you (only) have access via the much more secure
You can now redefine any required user- and group settings (e.g. for
Note that after updating the firmware, the NAS will spend a few hours reindexing the hard disks (searching for movies and audio-files) for the itunes and UPnP-services. You can stop this activity by deactivating the respective services.